Condition-Based Waiting

Overview

Flaky tests often guess at timing with arbitrary delays. This creates race conditions where tests pass on fast machines but fail under load or in CI.

Core principle: Wait for the actual condition you care about, not a guess about how long it takes.

When to Use

Decision flow: Test uses setTimeout/sleep? → Testing actual timing behavior? → (yes: document WHY timeout needed) | (no: use condition-based waiting)

Use when: Arbitrary delays (setTimeout , sleep ) | Flaky tests (pass sometimes, fail under load) | Timeouts in parallel runs | Async operation waits

Don't use when: Testing actual timing behavior (debounce, throttle) - document WHY if using arbitrary timeout

Core Pattern

// ❌ BEFORE: Guessing at timing await new Promise(r => setTimeout(r, 50)); const result = getResult(); expect(result).toBeDefined();

// ✅ AFTER: Waiting for condition await waitFor(() => getResult() !== undefined); const result = getResult(); expect(result).toBeDefined();

Quick Patterns

Scenario Pattern

Wait for event waitFor(() => events.find(e => e.type === 'DONE'))

Wait for state waitFor(() => machine.state === 'ready')

Wait for count waitFor(() => items.length >= 5)

Wait for file waitFor(() => fs.existsSync(path))

Complex condition waitFor(() => obj.ready && obj.value > 10)

Implementation

Generic polling: waitFor(condition, description, timeoutMs=5000)

• poll every 10ms, throw on timeout with clear message. See @example.ts for domain-specific helpers (waitForEvent , waitForEventCount , waitForEventMatch ).

Common Mistakes

❌ Bad ✅ Fix

Polling too fast (setTimeout(check, 1) ) Poll every 10ms

No timeout (loop forever) Always include timeout with clear error

Stale data (cache before loop) Call getter inside loop for fresh data

When Arbitrary Timeout IS Correct

await waitForEvent(...); await setTimeout(200)

• OK when: (1) First wait for triggering condition (2) Based on known timing, not guessing (3) Comment explaining WHY (e.g., "200ms = 2 ticks at 100ms intervals")

Real-World Impact

Fixed 15 flaky tests across 3 files: 60% → 100% pass rate, 40% faster execution, zero race conditions.

Blocker Criteria

STOP and report if:

Decision Type Blocker Condition Required Action

Timing behavior Test is intentionally testing timing (debounce, throttle) STOP and document WHY timeout is correct

Condition identification Cannot determine what condition to wait for STOP and analyze expected state change

Timeout configuration No maximum timeout defined for wait loop STOP and add timeout with clear error message

Polling interval Polling faster than 10ms without justification STOP and adjust to 10ms minimum

Cannot Be Overridden

The following requirements CANNOT be waived:

• Wait loops MUST have maximum timeout - infinite loops are FORBIDDEN

• Polling interval MUST NOT be less than 10ms without documented justification

• Condition function MUST call getter inside loop for fresh data - stale data caching is FORBIDDEN

• Arbitrary timeouts MUST have documented reasoning if used alongside condition-based waiting

• Timeout error messages MUST describe what condition was being waited for

Severity Calibration

Severity Condition Required Action

CRITICAL Wait loop without timeout (potential infinite loop) MUST add timeout immediately

CRITICAL Polling at 1ms intervals (CPU thrashing) MUST increase to minimum 10ms

HIGH Stale data - condition checked against cached value MUST move getter call inside loop

HIGH Arbitrary timeout without condition-based wait first MUST add condition wait before timeout

MEDIUM Timeout error message lacks context Should add descriptive failure message

LOW Polling interval could be optimized Fix in next iteration

Pressure Resistance

User Says Your Response

"Just increase the timeout, the test is flaky" "Increasing timeouts masks race conditions. MUST identify actual condition to wait for instead."

"Adding a small sleep is simpler" "Arbitrary sleeps cause flaky tests. MUST wait for the actual state change condition."

"The 10ms polling is too slow" "Polling faster than 10ms risks CPU thrashing. MUST justify with documented performance requirement."

"We don't need a timeout, it will always complete" "CANNOT have wait loops without timeout. Infinite loops are FORBIDDEN - add max timeout."

Anti-Rationalization Table

Rationalization Why It's WRONG Required Action

"A small sleep is good enough for this test" Arbitrary delays cause flaky tests under load MUST use condition-based waiting

"Polling every 1ms will be faster" CPU thrashing harms overall test performance MUST use minimum 10ms interval

"This will always complete quickly" Assumptions about timing fail in CI/parallel runs MUST add timeout with error message

"The timeout handles the failure case" Timeout masks root cause; condition reveals intent MUST wait for condition, timeout is safety net

"Test is testing timing, so timeout is fine" Timing tests still need documented justification MUST document WHY timeout is correct